华为组播实验,PIM-DM组播实验
一、配置VLAN,并将端口加入VLAN
LSW5:
system
vlan batch 10 to 100
int g 0/0/1
port link-type trunk
port trunk allow pass vlan all
int g 0/0/3
port link-type trunk
port trunk allow pass vlan all
ing g 0/0/2
port link-type access
port default vlan 10
其余交换机配置几乎相同,略
二、配置VLANif接口
LSW5:
system
int vlanif 10
ip ad 10.10.0.1 24
int vlanif 40
ip ad 10.40.0.1 24
int vlanif 70
ip ad 10.70.0.1 24
其余交换机配置几乎相同,略
三、配置路由协议,使以上设备能够相互通信
LSW5:
ospf 100
area 0
network 10.10.0.1 0.0.0.0
network 10.40.0.1 0.0.0.0
network 10.70.0.1 0.0.0.0
### 将自身的IP地址宣告出去
其余交换机配置几乎相同,略。配置完成后,所有设备都能相互ping通,确认好再进行下一步。
四、开启组播路由功能
LSW5:
multicast routing-enable
int vlanif 10
pim dm
int vlanif 40
pim dm
int vlanif 70
pim dm
其余交换机配置几乎相同,略。
五、在连接用户主机的接口上使能IGMP
LSW5:
int vlanif 10
igmp enable
六、验证结果
使用命令 display pim interface
命令查看接口上PIM的配置和运行情况。需要State字段显示为up,表示PIM邻居成功建立。
<Huawei>dis pim int
VPN-Instance: public net
Interface State NbrCnt HelloInt DR-Pri DR-Address
Vlanif10 up 0 30 1 10.10.0.1 (local)
Vlanif70 up 1 30 1 10.70.0.2
Vlanif40 up 1 30 1 10.40.0.2
七、配置组播地址
MCS1:
PC1:
1、然后点击图片上的 启动VLC
2、找到MCS1,选择一段视频,点击运行,但是弹出了如下窗口
PS:MP4视频我在//www.vjshi.com/上面随便下载的
八、下载VLC播放器
//www.videolan.org/vlc/
下载安装完成后,在ENSP右上角的 齿轮(设置)=>工具设置=>VLC中选择刚才安装好的目录下的vlc.exe。
再点击运行,PC1就能接收到MSC1发送来的视频啦。
可以在SW5上查看组播路由表:
<Huawei>dis pim routing-table
VPN-Instance: public net
Total 1 (*, G) entry; 1 (S, G) entry
(*, 239.1.1.1)
Protocol: pim-dm, Flag: WC
UpTime: 01:10:02
Upstream interface: NULL
Upstream neighbor: NULL
RPF prime neighbor: NULL
Downstream interface(s) information:
Total number of downstreams: 1
1: Vlanif10
Protocol: igmp, UpTime: 01:10:02, Expires: never
(10.100.0.2, 239.1.1.1)
Protocol: pim-dm, Flag: ACT
UpTime: 00:01:19
Upstream interface: Vlanif70
Upstream neighbor: 10.70.0.2
RPF prime neighbor: 10.70.0.2
Downstream interface(s) information:
Total number of downstreams: 1
1: Vlanif10
Protocol: pim-dm, UpTime: 00:01:19, Expires: -